TR8 www.vishay.com vishay sprague revision: 09-aug-11 1 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 solid tantalum chip capacitors m icro t an tm low esr, leadframeless molded features ? lead (pb)-free face -down terminations ? mounting: surface mount ? 8 mm tape and reel packaging available per eia-481 and reeling per iec 60286-3 7" [178 mm] standard ?low esr ? compliant to rohs directive 2002/95/ec note ** please see document vishay material category policy: www.vishay.com/doc?99902 performance characteristics operating temperature: - 55 c to + 85 c (to + 125 c voltage derating) capacitance range: 1 f to 220 f capacitance tolerance: 20 % standard, 10 % available voltage range: 4 v dc to 16 v dc notes ? we reserve the right to supply higher voltage ratings and tigh ter capacitance tolerance capacitors in the same case size. voltage substitutions will be marked with the higher voltage rating. (1) the eia and cecc standards for low esr solid tantalum chip capacitors, allow delta esr of 1.25 times the datasheet limit after mounting. ordering information TR8 m 106 m 6r3 c 2000 type case code capacitance capacitance tolerance dc voltage rating at + 85 c termination esr see ratings and case codes table this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. k = 10 % m = 20 % this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an r (6r3 = 6.3 v). c = 100 % tin 7" [178 mm] reel maximum 100 khz esr in (m ? ) (1) dimensions in inches [millimeters] case code l w h p1 p2 c m 0.063 0.008 [1.60 0.2] 0.033 0.008 [0.85 0.2] 0.031 0.004 [0.80 0.1] 0.020 0.004 [0.50 0.1] 0.024 0.004 [0.60 0.1] 0.024 0.004 [0.60 0.1] p 0.094 0.004 [2.4 0.1] 0.057 0.004 [1.45 0.1] 0.043 0.004 [1.10 0.1] 0.020 0.004 [0.50 0.1] 0.057 0.004 [1.40 0.1] 0.035 0.004 [0.90 0.1] l anode polarity bar anode termination h w p1 c p2 p1 cathode termination
TR8 www.vishay.com vishay sprague revision: 09-aug-11 2 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) preliminary values, contact factory for availability ratings and case codes f 4 v 6.3 v 10 v 16 v 1.0 m 4.7 m (1) 10 m m 15 m 22 m 33 m m 47 m p (1) 220 p marking voltage code capacitance code vcodecap, fcode 4.0 g 33 n 6.3 j 47 s 10 a 68 w 16 c 100 a 20 d 150 e 25 e 220 j standard ratings capacitance (f) case code part number max. dc leakage at + 25 c (a) max. df at + 25 c (%) max. esr at + 25 c 100 khz ( ? ) max. ripple 100 khz i rms (a) ? c/c (2) (%) 4 v dc at + 85 c; 2.7 v dc at + 125 c 33 m TR8m336m004c1500 2.6 30 1.50 0.129 20 47 m TR8m476m004c1500 3.8 40 1.50 0.129 30 220 p TR8p227(1)004c1000 17.6 30 1.00 0.212 30 6.3 v dc at + 85 c; 4 v dc at + 125 c 10 m TR8m106(1)6r3c2000 0.6 8 2.00 0.112 10 22 m TR8m226m6r3c1500 2.8 20 1.50 0.129 15 33 m TR8m336m6r3c1500 4.2 30 1.50 0.129 30 10 v dc at + 85 c; 7 v dc at + 125 c 10 m TR8m106m010c2000 1.0 20 2.00 0.112 15 15 m TR8m156(1)010c3000 1.5 30 3.00 0.091 20 47 p TR8p476m010c0800 (1) 4.7 22 0.80 0.237 20 47 p TR8p476m010c1000 4.7 22 1.00 0.212 20 16 v dc at + 85 c; 10 v dc at + 125 c 1.0 m TR8m105(1)016c9500 0.5 6.0 9.50 0.05 15 4.7 m TR8m475m016c4000 (1) 0.8 8.0 4.00 0.08 15 notes ? part number definition: (1) tolerance: for 10 % tolerance, specify k; for 20 % tolerance, change to m (1) preliminary values, contact factory for availability (2) see performance characteristics tables m-case voltage code a polarity bar p-case capacitance code j g voltage code polarity bar
TR8 www.vishay.com vishay sprague revision: 09-aug-11 3 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 capacitors performance characteristics notes ? at + 25 c , the leakage current shall not exceed the value listed in the standard ratings table. ? at + 85 c , the leakage current shall not exceed 10 times the value listed in the standard ratings table. ? at + 125 c , the leakage current shall not exceed 12 times the value listed in the standard ratings table. electrical performance characteristics item performance characteristics category temperature range - 55 c to + 85 c (to + 125 c with voltage derating) capacitance tolera nce 20 %, 10 % (at 120 hz) 2 v rms at + 25 c using a capacitance bridge dissipation factor (at 120 hz) limits per standard ratings ta ble. tested via bridge method, at 25 c, 120 hz. esr (100 khz) limits per standard ratings table. tested via br idge method, at 25 c, 100 khz. leakage current after application of rated voltage a pplied to capacitors for 5 min using a steady source of power with 1 k ? resistor in series with the capacitor under test, leakage current at 25 c is not more than described in standard ratings table. note that the leakage current varies with temperature and applied voltage. see graph below for the appropriate adjustment factor. reverse voltage capacitors are capable of withstanding peak voltages in the reverse direction equal to: 10 % of the dc rating at + 25 c 5 % of the dc rating at + 85 c vishay does not recommended intentional or repetitive application of reverse voltage temperature derating if capacitors are to be used at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors: 1.0 at + 25 c 0.9 at + 85 c 0.4 at + 125 c operating temperature + 85 c rating + 125 c rating working voltage (v) surge voltage (v) working voltage (v) surge voltage (v) 4.0 5.2 2.7 3.4 6.3 8.0 4.0 5.0 10 13 7.0 8.0 16 20 10 12 20 26 13 16 25 32 17 20 35 46 23 28 50 65 33 40 typical leakage current factor range 100 10 1.0 0.1 0.01 0.001 0 10 40 708090 60 50 20 30 100 + 125 c + 85 c + 55 c + 25 c 0 c - 55 c percent of rated volta g e leaka g e current factor
TR8 www.vishay.com vishay sprague revision: 09-aug-11 4 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 environmental performance characteristics item condition post test performance life test at + 85 c 1000 h application of rated voltage at 85 c with a 3 ? series resistance, mil-std 202g method 108a capacitance change dissipation factor leakage current refer to standard ratings table not to exceed 150 % of initial not to exceed 200 % of initial humidity tests at 40 c/90 % rh 500 h, no voltage applied mil-std 202g method 103b capacitance change dissipation factor leakage current refer to standard ratings table not to exceed 150 % of initial not to exceed 200 % of initial thermal shock at - 55 c/+ 125 c, 30 min each, for 5 cycles. mil-std 202g method 107g capacitance change dissipation factor leakage current refer to standard ratings table not to exceed 150 % of initial not to exceed 200 % of initial mechanical performance characteristics item condition post test performance terminal strength apply a pressure load of 5 n for 10 s 1 s horizontally to the center of capacitor side body. aec-q200 rev. c method 006 capacitance change dissipation factor leakage current refer to standard ratings table initial specified value or less initial specified value or less there shall be no mechanical or visual damage to capacitors post-conditioning. substrate bending (board flex) with parts soldered onto substrate test board, apply force to the test board for a deflection of 1 mm. aec-q200 rev. c method 005 capacitance change dissipation factor leakage current refer to standard ratings table initial specified value or less initial specified value or less vibration mil-std-202g, method 204d, 10 hz to 2000 hz, 20 g peak capacitance change dissipation factor leakage current refer to standard ratings table initial specified value or less initial specified value or less there shall be no mechanical or visual damage to capacitors post-conditioning. shock mil-std-202g, method 213b, condition i, 100 g peak capacitance change dissipation factor leakage current refer to standard ratings table initial specified value or less initial specified value or less there shall be no mechanical or visual damage to capacitors post-conditioning. resistance to solder heat at 260 c, for 10 s, reflow capacitance change dissipation factor leakage current refer to standard ratings table not to exceed 150 % of initial not to exceed 200 % of initial there shall be no mechanical or visual damage to capacitors post-conditioning. solderability mil-std-202g, method 208h, ansi/j-std-002, test b. applies only to solder and tin plated terminations. does not appl y to gold terminations. there shall be no mechanical or visual damage to capacitors post-conditioning. resistance to solvents mil-std-202, method 215d there shall be no mechanical or visual damage to capacitors post-conditioning. flammability encapsulation materials me et ul 94 v-0 with an oxygen index of 32 %.
TR8 www.vishay.com vishay sprague revision: 09-aug-11 5 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? metric dimensions will govern. dimensio ns in inches are rounded and for reference only. (1) a 0 , b 0 , k 0 , are determined by the maximum dimensions to the ends of the terminals extending from the component bo dy and/or the body dimensions of the component. the clearance between the ends of the terminals or body of the co mponent to the sides and depth of the cavity (a 0 , b 0 , k 0 ) must be within 0.002" (0.05 mm) minimum and 0.020" (0. 50 mm) maximum. the clearance allowed must also prevent rotation of the component within the cavity of not more than 20. (2) tape with components shall pass around ra dius r without damage. the minimum trailer length may require addi tional length to p rovide r minimum for 12 mm embossed tape for reels with hub diameters approaching n minimum. (3) this dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between th e embossed cavities or to the edge of the cavity whichever is less. (4) this dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed ca vity or to the edge of th e cavity whichever is less. (5) the embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. dimensions of embossement location shall be a pplied independent of each other. (6) b 1 dimension is a refere nce dimension tape feeder clearance only. plastic tape and reel packaging in inches [millimeters] tape and reel specifications: all case sizes are available on plastic emboss ed tape per eia-481. tape reeling per iec 60286-3 is also available. standard reel diameter is 7" [178 mm], 13" [330 mm] reels are available and recommended as the most cost effective packaging method. the most efficient packaging quantities are full reel increments on a given reel diameter. the quantities shown allow for the sealed empty pockets required to be in conformance with eia-481. reel size and packaging orientation must be specified in the vishay sprague part number. carrier tape dimensions in inches [millimeters] case code tape size b 1 (max.) d 1 (min.) f k 0 (max.) p 1 w p8 mm 0.108 [2.75] 0.039 [1.0] 0.138 0.002 [3.5 0.05] 0.054 [1.37] 0.157 0.004 [4.0 1.0] 0.315 + 0.0118/- 0.0039 [8.0 + 0.30/- 0.10] 0.004 [0.10] max. k 0 tape thickness b 1 (max.) (6) 0.014 [0.35] max. 10 pitches cumulative tolerance on tape 0.008 [0.200] embossment 0.069 0.004 [1.75 0.10] d 1 (min.) for components 0.079 x 0.047 [2.0 x 1.2] and larger (5) . maximum user direction of feed center lines of cavity a 0 p 1 f w 0.030 [0.75] min. (3) 0.030 [0.75] min. (4) 0.079 0.002 [2.0 0.05] 0.157 0.004 [4.0 0.10] 0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0] b 0 maximum component rotation (side or front sectional view) 20 for tape feeder reference only including draft. concentric around b 0 (5) deformation between embossments to p cover tape top cover tape cavity size (1) cathode (-) anode (+) direction of feed 20 maximum component rotation typical component cavity center line typical component center line a 0 b 0 (top view) 0.9843 [250.0] tape 3.937 [100.0] 0.039 [1.0] max. 0.039 [1.0] max. camber allowable camber to be 0.039/3.937 [1/100] (top view) non-cumulative over 9.843 [250.0]
TR8 www.vishay.com vishay sprague revision: 09-aug-11 6 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) a 0 , b 0 are determined by the maximum dimensions to the ends of th e terminals extending from the component body and/or the body dimensions of the component. the clearance between the ends of the terminals or body of the co mponent to the sides and depth of the cavity (a 0 , b 0 ) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm ) maximum. the clearance allowe d must also prevent rotation of the component within the cavity of not more than 20. paper tape and reel packaging in inches [millimeters] case size tape size a 0 b 0 d 0 p 0 p 1 p 2 efwt m8 mm 0.041 0.002 [1.05 0.05] 0.071 0.002 [1.8 0.05] 0.06 0.004 [1.5 0.1] 0.157 0.004 [4.0 0.1] 0.157 0.004 [4.0 0.1] 0.079 0.002 [2.0 0.05] 0.069 0.004 [1.75 0.1] 0.0138 0.002 [3.5 0.05] 0.315 0.008 [8.0 0.2] 0.037 0.002 [0.95 0.05] standard packaging quantity case code quantity (pcs/reel) 7" reel m 4000 p 3000 recommended voltage derating guidelines standard conditions. for example: output filters capacitor voltage rating operating voltage 4.0 2.5 6.3 3.6 10 6.0 16 10 20 12 25 15 35 24 50 28 severe conditions. for example: input filters capacitor voltage rating operating voltage 4.0 2.5 6.3 3.3 10 5.0 16 8.0 20 10 25 12 35 15 50 24 ? d 0 t bottom cover tape f p 1 a 0 b 0 e 2 p 2 w p 0 e 1 cavity s ize (1) bottom cover tape u s er feed direction cavity center line s top cover tape [10 pitche s cumulative tolerance on tape 0.2 mm] g anode
TR8 www.vishay.com vishay sprague revision: 09-aug-11 7 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 power dissipation case code maximum permissible power dissipation at + 25 c (w) in free air m 0.025 p 0.045 recommended reflow profiles t p lead (pb)-free t p sn/pb t p t l lead (pb)-free t l sn/pb t s min. lead (pb)-free t s min. sn/pb t s max. lead (pb)-free t s max. sn/pb t s lead (pb)-free t s sn/pb t l 260 c 225 c 10 217 c 183 c 150 c 100 c 200 c 150 c 60 to 150 60 to 90 60 pad dimensions in inches [millimeters] case code a (min.) b (nom.) c (nom.) d (nom.) m 0.039 [1.00] 0.028 [0.70] 0.024 [0.60] 0.080 [2.00] p 0.063 [1.60] 0.031 [0.80] 0.047 [1.20] 0.110 [2.80] temperature (c) 25 c all case codes preheat (t s ) t p c t l c t s max. c t s max. c (t p ) (t l ) t, s a b c d
TR8 www.vishay.com vishay sprague revision: 09-aug-11 8 document number: 40114 for technical questions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 guide to application 1. ac ripple current: the maximum allowable ripple current shall be determ ined from the formula: where, p = power dissipation in watts at + 25 c (see paragraph number 5 an d the table power dissipation) r esr = the capacitor equivale nt series resistance at the specified frequency 2. ac ripple voltage: the maximum allowable ripple voltage shall be determ ined from the formula: or, from the formula: where, p = power dissipation in watts at + 25 c (see paragraph number 5 an d the table power dissipation) r esr = the capacitor equivale nt series resistance at the specified frequency z = the capacitor impedance at the specified frequency 2.1 the sum of the peak ac voltage plus the applied dc voltage shall not exceed the dc voltage rating of the capacitor. 2.2 the sum of the negative peak ac voltage plus the applied dc voltage shall not allow a voltage reversal exceeding 10 % of the dc working voltage at + 25 c. 3. reverse voltage: these capacitors are capable of withstanding peak voltages in the reverse direction equal to 10 % of the dc rating at + 25 c, 5 % of the dc rating at + 85 c and 1 % of the dc rating at + 125 c. 4. temperature derating: if these capacitors are to be operated at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: 5. power dissipation: power dissipation will be affected by the heat sinking capability of the mounting surface. non-sinuso idal ripple current may produce heating effects which differ from those shown. it is important that the equivalent i rms value be established when calculating permissible operating levels. (power di ssipation calculated using + 25 c temperature rise.) 6. printed circuit board materials: molded capacitors are compatible with commonly used printed circuit board materials (alumina su bstrates, fr4, fr5, g10, ptfe-fluorocarbon and porcelanized steel). 7. attachment: 7.1 solder paste: the recommended thickness of the solder paste after application is 0.007" 0.001" [0.178 mm 0.025 mm]. care should be exercised in selecting the solder paste. the metal purity should be as high as practical. the flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the ex posure to soldering heat. in practice this can be aided by extending the solder preheat time at tempera tures below the liquidous state of the solder. 7.2 soldering: capacitors can be attached by conventional soldering techniques; vapor phase, convection reflow, infrared reflow, wave soldering and hot plate methods. the soldering profile charts show recommended time/te mperature conditions for soldering. preheating is recommended. the recommended maximum ramp rate is 2 c per s. attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. the soldering iron must never come in contact with the capacitor. 7.2.1 backward and forwar d compatibility: capacitors with snpb or 100 % tin termination finishes can be soldered using snpb or lead (pb)-free soldering processes. 8. cleaning (flux removal) after soldering: molded capacitors are compatible with all commonly used solvents such as tes, tms, prelete, chlorethane, terpene and aqueous clea ning media. however, cfc/ods products are not used in the production of these devices and are not recommended. solvents containing methylene ch loride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. 8.1 when using ultrasonic cleaning, the board may resonate if the output power is too high. this vibration can cause cracking or a decrease in the adherence of the termination. do not exceed 9w/l at 40 khz for 2 min. 9. recommended mounting pad geometries: proper mounting pad geometries are essential for successful solder connections. these dimensions are highly process sensitiv e and should be designed to minimize component rework due to unacceptable solder joints. the dimensional configurations shown are the recommended pad geometries for both wave and reflow soldering techniques. these dimensions are intended to be a starting point for circuit board designers and may be fine tuned if necessary based upon the peculiarities of the soldering process and/or circuit board design. temperature derating factor + 25 c 1.0 + 85 c 0.9 + 125 c 0.4 i rms p r esr ------------ = v rms z p r esr ------------ = v rms i rms x z = product information moisture sensitivity www.vishay.com/doc?40135 selector guides solid tantalum selector guide www.vishay.com/doc?49053 solid tantalum chip capacitors www.vishay.com/doc?40091 faq frequently asked questions www.vishay.com/doc?40110
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
